DIY मीडिया होम लोगो

अपनी खुद की होम थिएटर और हाय-Fi सेटअप डिजाइन और बनाने के लिए परम साइट.

0विंडोज़ 8 प्रतीक चिन्हWdsclient - WDS मोड आरंभ करने में समस्या थी

मैं पिछले कुछ वर्षों में इस त्रुटि के लिए कई बार मिला है, और यह हमेशा एक अलग कारण के लिए हो रहा है. तो नीचे मैं इस समस्या के सभी संभव स्रोतों मुक़ाबला होगा मैं अब तक का सामना करना पड़ा, समाधान के साथ-साथ

1. WDS सर्वर भी DHCP सर्वर और विकल्प है 67 सही ढंग से सेट नहीं है

If one serv­er is run­ning both WDS and DHCP you will need to change a few set­tings as both ser­vices nor­mally listen on the same port. You need to tell WDS to listen on a dif­fer­ent port and set DHCP to listen for and pass on PXE requests. There is plenty of doc­u­ment­a­tion on this from Microsoft or via Google.

2. एक VMware प्रणाली कहीं नेटवर्क पर चल रहा है और एक समानांतर डीएचसीपी सेवा चल रही है

I’ve had this before — hav­ing VMware work­sta­tion (and prob­ably oth­er products) run­ning on any PC on the net­work seems to some­times mess up DHCP by issu­ing an आईपी to anoth­er cli­ent PC when it should­n’t be doing any­thing of the sort!

3. एनआईसी ड्राइवरों बूट छवि में शामिल नहीं हैं (नहीं स्थापित छवि, बूट छवि)

If the NIC drivers aren’t included in the boot image it will fail after the ini­tial PXE boot. Adding the drivers is reas­on­abl ystraight-for­ward, but beware a sep­ar­ate prob­lem where WDS on Win­dows Serv­er 2012 R2 can­’t add drivers to Win­dows 10 बूट छवियों. I have writ­ten about how to solve this in a pre­vi­ous post.

4. ग्राहक पीसी एकाधिक एनआईसी है

Some cli­ent पीसी have mul­tiple NICs — if neces­sary dis­able addi­tion­al NICs pri­or to the deployment

5. क्लाइंट और अलग सबनेट पर WDS सर्वर

You will need to do some addi­tion­al con­fig­ur­a­tion to pass the PXE request through from 1 sub­net to the oth­er. There is plenty of doc­u­ment­a­tion on this avail­able from Microsoft and via Google.

6. एक स्थिर निरुपित आईपी अपने DHCP सर्वर पर मेजबान पीसी के लिए

This was this issue I had most recently — the PC was get­ting 1 आईपी address at the ini­tial PXE boot and then seemed to get assigned anoth­er one after boot which seemed to pre­vent the serv­er from see­ing it. By adding a stat­ic mapped आईपी पीसी के मैक पता पता यह हमेशा एक ही हो जाता है आईपी address and then the error does­n’t occur. सफलता.

उत्तर छोड़ दें